It is indicating equipment forms the central part of a fire detection and alarm system. And it is the central part of conventional fire alarm system, designed for applications requiring gas leak detector, bell, manual pull stations, and sprinkler supervision. Each zone can be disabled by a button.
Our of offer a quality tested assortment of Manual Call Point. These products are widely demanded by the clients for their durability and high tensile strength. This call point is specially designed for the purposes of raising an alarm manually at the time of emergency. Moreover, we have proved our credibility in thus able to get recurrent orders from our prestigious clients.
Our of Hooter is a premium quality Hooters & sounder. Hooter in are manufactured by using quality assured material and advanced techniques, which make them up to the standard in this highly challenging field. The materials utilized to manufacture Hooter in is sourced from the most reliable and official Hooters & Sounder vendors, chosen after performing detailed market surveys. Thus, our products are widely acknowledged in the market for their high quality. We are dedicatedly involved in providing an excellent quality array of Hooters & sounder.
The Conventional Photo–electronic smoke detector uses a state of-the-art optical sensing chamber. This detector is designed to provide open area protection and to be used with most conventional fire alarm panel. The Conventional rate of rise smoke detector uses thermal component to detect the temperature changing in the environment. It can enable fire alarm when the temperaturedifference achieved the setting rate of rise temperature value.reach the setting fixed value. It has a stable and reliable workingperformance. Two LEDs on each detector provide local 360 visible alarm Indication. They flash every six seconds indicating that power Is applied and the detector is working properly. The LEDs latch On in alarm. LEDs will be off when a trouble condition exists that the detector sensitivity is outside the listed limit. The alarm can be reset only by a momentary power interruption. The detector that initiated the alarm condition will have its red LED and relays latched until reset by panel.
The Conventional heat detector uses a state of-the-art optical sensing chamber. This detector is designed to provide open area protection and to be used with most conventional fire alarm panel. The Conventional rate of rise heat detector uses thermal component to detect the temperature changing in the environment. It can enable fire alarm when the temperaturedifference achieved the setting rate of rise temperature valuereach the setting fixed value. It has a stable and reliable workingperformance. Two LEDs on each detector provide local 360 visible alarm Indication. They flash every six seconds indicating that power Is applied and the detector is working properly. The LEDs latch On in alarm. LEDs will be off when a trouble condition exists that the detector sensitivity is outside the listed limit. The alarm can be reset only by a momentary power interruption. The detector that initiated the alarm condition will have its red LED and relays latched until reset by panel.
The Standalone detector is 9v operated. Standalone Photoelectric Smoke Detector can detect a large amount of smoke when fire generated sending alarm signal in time. Alarm adopts photoelectric smoke devices and excellent production technology, work stability, beautiful appearance, easy to install, without debugging, which can be widely used in hotels, stores, Internet, cafes, coffee shop, lounge and residential places on fire safety monitoring.
Our+B6 Manufacturer of Fire Alarm Systems UV Flame Detectors Respond to radiation in the spectral range of approximately 180-260 nanometers. They offer quick response and good sensitivity at comparatively short ranges (0 – 50 ft). Because they are susceptible to arc welding, halogen lamps, and electrical discharges like lightning, they tend to be sited indoors. Thick, sooty smoke can also cause failures due to attenuation of the incident UV radiation. Dual LED for 360 degree visibility, 02 Wire based model Easy installation and maintenance High Sensitivity and wide directivity Sleek low-profile housing design Quick detection of flame from distance SMD circuit board design- satisfactory quality and reliability Guaranteed
Conventional Reflective Beam Detector is a reflective infrared beam detector, which must be used together with a reflector. With excellent built-in microprocessor, the detector has strong ability of analysis andjudgment. The detector can automatically carry out systemadjustment, compensationof variation of ambient data, and judgment of fire and fault through fixed algorithm, andindicate these states by LED and signal output terminals. Unit has an emitter and the receiver as one. In that case, it has advantages of easy and convenient installation as we have wonderful collimation for the optical path Automatic calibration to make sure one person can debug the device easily Self-testing function to monitor the internal fault of the detector
Available with us is a wide array of Gas Leak Detectors for LPG and Natural Gas. These systems works as the complete gas-leaking alarming products that are ideal for detecting the leakage of particular gas and alarms. It gives out audio alarming facility. Known for their efficient working and longer service life, Hot wire type sensor Modernized design Yellow LED shows sensor faulty mode Detect all sorts of combustible gases, LPG and LNG include city gas Ideal for all kitchens
Our Response Indicators are connected to automatic Fire Detectors in order to indicate quickly the source of an alarm signal from Detectors which are not easily accessible or visible. The Response Indicators contain an indicator lamp unit with one resp. two LED. They light up as soon as the connected fire detector gives an alarm. Only one external response indicator may be connected to each detector.
It is indicating equipment forms the central part of a fire detection and alarm system. The 2-wire is compatible with this devices. And it is the central part of conventional fire alarm system, designed for applications requiring smoke detector, bell, manual pull stations, and sprinkler supervision. Each zone can be disabled by a button. This panel allows the user to monitoring Fire alarm system along with the provision to make live/ pre recorded announcements. In built speaker is used to produce voice alarms and also facilities instant two way communications with the talkback unit. This panel can control external speakers individually for making announcements, playing music etc.
